焊接热循环 weld thermal cycle
焊接温度场 field of weld temperature; weld temperature field
准稳定温度场 quasi-stationary temperature field
焊接热源 welding heat source
点热源 point heat source
线热源 linear heat source
面热源 plane heat source
瞬时集中热源 instantaneous concentration heat source
热效率 thermal efficiency
热能集中系数 coefficient of heat flow concentration
峰值温度 peak temperature
瞬时冷却速度 momentary cooling rate
冷却时间 cooling time
置换氧化 substitutionary oxydation
扩散氧化 diffusible oxydation
脱氧 desoxydation
先期脱氧 precedent desoxydation
扩散脱氧 diffusible desoxydation
沉淀脱氧 precipitation desoxydation
扩散氢 diffusible hydrogen
初始扩散氢 initial diffusible hydrogen
100℃残余扩散氢 diffusible hydrogen remained at 100℃
残余氢 residual hydrogen
去氢 dehydrogenation
去氢热处理 heat treatment for dehydrogenation
脱硫 desulphurization
脱磷 dephosphorization
渗合金 alloying
微量合金化 microalloying
一次结晶组织 primary solidification structure
二次结晶组织 secondary solidification structure
联生结晶 epitaxial solidification
焊缝结晶形态 solidification mode in weld-bead
结晶层状线 ripple
多边化边界 polygonization boundary
结晶平均线速度 mean solidification rate
针状铁素体 acicular ferrite
条状铁素体 lath ferrite
侧板条铁素体 ferrite side-plate
晶界欣素体 grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite
粒状贝氏体 granular bainite
板条马氏体 lath martensite
过热组织 overheated structure
魏氏组织 Widmannst?tten structure
M-A组元 martensite-austenite constituent
焊件失效分析 failure analysis of weldments
冷裂判据 criterion of cold cracking
冷裂敏感系数 cold cracking susceptibity coefficient
脆性温度区间 brittle temperature range
氢脆 hydrogen embrittlement
层状偏析 lamellar segregation
愈合 healing effect
断口金相fractography
断口 fracture
延性断口 ductile fracture
韧窝断口dimple fracture
脆性断口 brittle fracture
解理断口 cleavage fracture
准解理断口 quasi-cleavage fracture
氢致准解理断口 hydrogen-embrittlement induced
沿晶断口 intergranular fracture
穿晶断口 transgranular fracture
疲劳断口 fatigue fracture
滑移面断口 glide plane fracture
断口形貌 fracture apperance
断口试验 fracture test
宏观断口分析 macrofractography
放射区 radical zone
纤维区 fibrous zone
剪切唇区 shear lip aone
焊接性weldability
使用焊接性 service weldability
工艺焊接性 fabrication weldability
冶金焊接性 metallurgical weldability
热焊接性 thermal weldability
母材 base metal; parent metal
焊接区 weld zone
焊态 as-welded (AW)
母材熔化区 fusion zone
半熔化区 partial melting region
未混合区 unmixed zone
熔合区 bond area
熔合线 weld junction (英)；bond line (美)
热影响区 heat-affected zone (HAZ)
过热区 overheated zone
粗晶区 coarse grained region
细晶区 fine grained region
过渡区 transition zone
硬化区 hardened zone
碳当量 carbon equivalent
铬当量 chromium equivalent
镍当量 nickel equivalent
舍夫勒组织图 Schaeffler's diagram
德龙组织图 Delong’s diagram
连续冷却转变图（CCT图）continuous cooling transformation
裂纹敏感性 cracking sensibility
焊接裂纹 weld crack
焊缝裂纹 weld metal crack
焊道裂纹 bead crack
弧坑裂纹crater crack
热影响区裂纹 heat-affected zone crack
纵向裂纹 longitudinal crack
横向裂纹 transverse crack
微裂纹 micro-crack; micro-fissure
热裂纹 hot crack
凝固裂纹 solidification crack
晶间裂纹 intercrystalline crack
穿晶裂纹 transcrystalline crack
多边化裂纹 polygonization crack
液化裂纹 liquation crack
失延裂纹 ductility-dip crack
冷裂纹 cold crack
延迟裂纹 delayed crack
氢致裂纹 hydrogen-induced crack
焊道下裂纹 underbead crack
焊根裂纹 root crack
焊趾裂纹 toe crack
锯齿形裂纹 chevron cracking
消除应力处理裂纹 stress relief annealing crack (SR crack)
再热裂纹 reheat crack
焊缝晶间腐蚀 weld intercryctalline corrosion
刀状腐蚀 knife line attack
敏化区腐蚀 weld decay
层状撕裂 lamellar tearing
焊接性试验 weldability
裂纹试验 cracking test
IIW裂纹试验 IIW cracking test
Y形坡口裂纹试验 slit type cracking test
分块形槽热裂纹试验 segmented circular groove cracking test
H形裂纹试验 H-type cracking test
鱼骨形裂纹试验 fishbone cracking test
指形裂纹试验 finger (cracking) test
T形裂纹试验 Tee type cracking test
环形槽裂纹试验 circular-groove cracking test
可调拘束裂纹试验 varestraint test
BWRA奥氏体钢裂纹试验 BWRA cracking test for austenitie steel
圆棒裂纹试验 bar type cracking test; round bar cracking test
里海裂纹试验 Lehigh restraint cracking test
圆形镶块裂纹试验 circular-path cracking test
十字接头裂纹试验 cruciform cracking test
Z向窗口拘束裂纹试验 Z-direction window type restraint cracking test
G-BOP焊缝金属裂纹试验 G-BOP weld metal crack test
巴特尔焊道下裂纹试验 Battelle type underbead cracking test
U形拉伸试验 U-tension test
缪雷克期热裂纹试验 Murex hot cracking test
菲斯柯裂纹试验 FISCO (type) cracking test
CTS裂纹试验 controlled thermal severity
拉伸拘束裂纹试验（TRC试验）tensile restraint cracking test
刚性拘束裂纹试验（RRC试验）rigid restraint cracking test
插销试验 implant test
Tigamajig 薄板焊接裂纹试验 Tigamajing thin plate cracking test
焊道纵向弯曲试验 longitudinal-bead test
柯麦雷尔弯曲试验 Kommerell bead bend test
肯泽尔弯曲试验 Kinzel test
缺口弯曲试验 notch bend test
热朔性试验 hot-ductility test
热影响区冲击试验 impact test of HAZ
热影响区模拟试验 synthetic heat-affected zone test
最高硬度试验 maximum hardness test
落锤试验 NRL (Naval Research Laboratory)
测氢试验 Hydrogen test
焊接材料
电极
焊接材料welding consumables
电极electrode
熔化电极consumable electrode
不熔化电极nonconsumable electrode
钨电极tungsten electrode
焊丝welding wire. Welding rod
实心焊丝solid wire
渡铜焊丝copper-plating welding wire
自保护焊丝self-shielded welding wire
药芯焊丝flux-cored wire
复合焊丝combined wire
堆焊焊丝surfacing welding rod
填充焊丝filler wire
焊条electrode/ covered electrode
焊芯core wire
药皮coating (of an electrode)/ covering (of an electrode)
涂料coating flux/coating material
造气剂gas forming constituents
造渣剂slag forming constituents
合金剂alloying constituent
脱氧剂dioxidizer
稳弧剂arc stabilizer
粘接剂binder
水玻璃water glass
水玻璃模数modules of water glass
酸性焊条acid electrode
高钛型焊条high titania (type) electrode
钛钙型焊条lime titania type electrode
钛铁矿形焊条ilmenite type electrode
氧化铁型焊条iron oxide type electrode/ high iron oxide type electrode
高纤维素型焊条high cellulose (type) electrode
石墨型焊条graphite type electrode
碱性焊条basic electrode/ lime type covered electrode
低氢型焊条low hydrogen type electrode
高韧性超低氢焊条high toughness super low hydrogen electrode
奥氏体焊条austenitic electrode
铁素体焊条ferritic electrode
不锈钢焊条stainless steel electrode
珠光体耐热钢焊条pearlitic heat resistant steel electrode
低温钢焊条low temperature steel electrode/ steel electrode for low temperature
铝合金焊条aluminum alloy arc welding electrode
铜合金焊条copper-alloy arc welding electrode
铜芯铸铁焊条cast iron electrode with steel core
纯镍铸铁焊条pure nickel cast iron electrode
球墨铸铁焊条electrode for welding spheroidal graphite cast iron
铸芯焊条electrode with cast core wire
镍基合金焊条nickel base alloy covered electrode
蒙乃尔焊条Monel electrode
纯铁焊条pure iron electrode
渗铝钢焊条alumetized steel electrode
高效率焊条high efficiency electrode
铁粉焊条iron powder electrode
底层焊条backing welding electrode
深熔焊条deep penetration electrode
重力焊条gravity electrode
立向下焊条electrode for vertical down position welding
节能焊条saving energy electrode
水下焊条underwater welding electrode
耐海水腐蚀焊条seawater corrosion resistant steel electrode
低尘低毒焊条low-fume and harmfulless electrode/
low-fume and low-toxic electrode
堆焊焊条surfacing electrode
耐磨堆焊焊条hardfacing electrode
钴基合金堆焊焊条cobalt base alloy surfacing electrode
碳化钨堆焊焊条tungsten carbide surfacing electrode
高锰钢堆焊焊条high manganese steel surfacing electrode
双芯焊条twin electrode
绞合焊条stranded electrode
编织焊条braided electrode
双层药皮焊条double coated electrode
管状焊条flux-cored electrode
气渣联合保护型药皮semi-volatile covering
焊条工艺性usability of the electrode/ technicality of the electrode
焊条使用性running characteristics of an electrode/ operating characteristics of an electrode
焊条熔化性melting characteristics of an electrode
焊条直径core diameter
焊条偏心度eccentricity (of an electrode)
药皮重量系数gravity coefficient of coating
焊条药皮含水量percentage of moisture for covering
焊条夹吃持端bare terminal (of an electrode)
焊条引弧端striking end (of an elcetrode)
焊剂welding flux/ flux
熔炼焊剂fused flux
粘结焊剂bonded flux
烧结焊剂sintered flux/ agglomerated flux
窄间隙埋弧焊焊剂flux for narrow-gap submerged arc welding
低氢型焊剂low hydrogen type flux
高速焊剂high speed welding flux
无氧焊剂oxygen-free flux
低毒焊剂low poison flux
磁性焊剂magnetic flux
电弧焊 arc welding
直流电弧焊 direct current arc welding
交流电弧焊 alternating current arc welding
三相电弧焊 three phase arc welding
熔化电弧焊 arc welding with consumable
金属极电弧焊 metal arc welding
不熔化极电弧焊 arc welding with nonconsumable
碳弧焊 carbon arc welding
明弧焊 open arc welding
焊条电弧焊 shielded metal arc welding (SMAW)
重力焊gravity welding
躺焊 fire cracker welding
电弧堆焊 arc surfacing
自动堆焊 automatic surfacing
躺板极堆焊 surfacing by fire cracker welding
带极堆焊 surfacing with band-electrode
振动电弧堆焊 vibratory arc surfacing
耐磨堆焊 hardfacing
埋弧焊 submerged arc welding (SAW)
多丝埋弧焊multiple wire submerged arc welding
纵列多丝埋弧焊 Tandem sequence (submerged-arc welding)
横列多丝埋弧焊 series submerged arc welding (SAW-S)
横列双丝并联埋弧焊 transverse submerged arc welding
热丝埋弧焊 hot wire submerged-arc welding
窄间隙埋弧焊 narrow-gap submerged arc welding
弧压反馈电弧焊 arc voltage feedback controlling arc welding
自调节电弧焊 self-adjusting arc welding
适应控制焊接 adaptive control welding
焊剂层 burden; flux layer
气体保护电弧焊 gas shielded arc welding
保护气体 protective atmosphere
惰性气体 inert-gas
活性气体 active-gas
惰性气体保护焊 inert-gas (arc) welding
氩弧焊 argon arc welding
熔化极惰性气体保护电弧焊 metal inert-gas arc welding
钨极惰性气体保护电弧焊 tungsten inert-gas arc welding
钨极氢弧焊 argon tungsten arc welding
脉冲氢弧焊 pulsed argon arc welding
熔化极脉冲氢弧焊 argon metal pulsed arc welding
钨极脉冲氢弧焊 argon tungsten pulsed arc welding
热丝MIG焊 hot wire MIG welding
热丝TIG焊 hot wire TIG welding
氨弧焊 helium-arc welding
活性气体保护电弧焊 metal active-gas arc welding
混合气体保护电弧焊 mixed gas arc welding